How long does a ground screw pile last: why some say 25 years and others 200

  1. Where the 25 to 200 years come from
  2. How the service life of a pile is calculated
  3. What determines how long a pile will last
  4. The weakest spot is not underground
  5. Should a pile be filled with concrete?
  6. Warranty and service life are different things
  7. How to check a pile before buying
  8. When a galvanized pile will not reach the stated service life
  9. Questions from customers

A galvanized SP Premier ground screw pile is designed for 50–120 years: at least 50 years, and up to 120 in non-aggressive soil. This is an estimate of service life based on metal thickness and corrosion rate, not a warranty: the warranty on the piles is 20 years. How long a pile will last depends on three things: the galvanizing method and zinc thickness, the pipe wall thickness and how aggressive the soil is. Figures like "100", "150" or "200 years" promise nothing without these three conditions.

Are you comparing ground screw piles with concrete and worried that metal in the ground will rot within a few years? Or does one seller say "up to 60 years" and another "up to 200", and you do not know whom to believe? We reviewed 27 pages of ground screw pile sellers in Kyiv (October 2026). The service life stated there ranges from 25 to 200 years, and not a single page gives the calculation method.

Below we explain how to read these figures, how the service life of ground screw piles is calculated and what to check before buying. For the foundation itself, see the article "Pile foundation on ground screw piles". And if you already have a site and are unsure about the soil, you do not have to figure it all out yourself. Message us at +38 050 431-70-60 (Viber, WhatsApp, Telegram): we will select a pile based on a description of the soil and the structure.

Galvanized SP Premier ground screw piles screwed in on a site for a foundation

Galvanized SP Premier ground screw piles on a site for a foundation

Where the 25 to 200 years come from

The service life of a ground screw pile is the number of years it carries the design load. First the zinc protects it from corrosion, then the reserve of pipe wall thickness does the work. The figures in listings describe different products in different soils, so "60 years" and "200 years" cannot be compared directly. Below are the types of piles and what each means for service life.

Pile type What protects the steel What it means for service life
Painted, no zinc Paint or primer paint. A scratch during screwing exposes the metal The shortest service life: where the paint is scratched, the steel is protected only by the wall thickness
Cold galvanizing Paint with zinc powder This is paint, not a zinc layer bonded with the steel. Hot-dip galvanizing service life figures do not apply to it
Thin hot-dip galvanizing Zinc bonded with the steel, but thin Service life depends on the layer thickness. Without a figure in µm it cannot be estimated
Hot-dip galvanizing 70 ± 10 µm, non-aggressive soil A thick zinc layer plus a 2–3 mm wall An estimated 50–120 years. This is how SP Premier piles are made
A pile whose listing only says "lasts up to 200 years" The seller does not say There is no way to check such a figure: neither the galvanizing method and zinc thickness, nor the wall thickness, nor the soil is stated. Ask the seller for this data

Sometimes the same page says "service life 100 years", "warranty 50 years", and further down mentions 25. Estimated service life and warranty are mixed up here, and the buyer cannot see what is a calculation and what is a promise. On another page the seller admits that "over 100 years" is unrealistic and that a pile without coating lasts up to 30 years. The honest answer is a range with conditions: for which pile and in which soil.

A service life figure without the zinc thickness in µm, the wall thickness and the soil type is advertising, not a calculation.

How the service life of a pile is calculated

Service life consists of two periods. The first is how many years it takes the soil to "eat" the zinc layer. The second is how long the pipe wall then keeps thinning while the pile still carries the load. Both depend on the corrosion rate: how many micrometres of metal the soil removes per year.

The formula in words:

  1. Zinc years = zinc thickness (µm) ÷ zinc corrosion rate in this soil (µm per year).
  2. Wall years = wall reserve (µm) ÷ steel corrosion rate in this soil (µm per year).
  3. Service life = zinc years + wall years.

Take the SPGS F 60 × 3 × 1200 (500) pile: zinc 70 ± 10 µm, wall 3 mm. The corrosion rate of zinc and steel differs many times over from soil to soil, so there is no single figure for every site. That is why, even for one pile model, SP Premier gives a range rather than a single figure.

The wall reserve is not the whole wall. A pile carries the load as long as the pipe cross-section is sufficient. So the calculation includes only the part of the wall that can be lost without reducing the bearing capacity.

Hence a range instead of a single figure. The same product lasts less in aggressive soil: the corrosion rate there is higher, and both periods get shorter. SP Premier estimates the service life of its piles at 50–120 years, with the upper limit applying to non-aggressive soil. Saline, acidic and peat sites are a separate case, covered below.

If the soil eats away metal twice as fast, both periods of service life become twice as short.

What determines how long a pile will last

Five factors affect the service life of a pile: the galvanizing method, the zinc thickness, the wall thickness, the soil and the installation. The first three are set by the manufacturer, the soil depends on the site and the installation on the crew.

Galvanizing method: hot-dip, cold or electroplated

SP Premier piles are hot-dip galvanized to DIN EN ISO 1461: the pile is dipped into molten zinc, and the zinc bonds with the steel surface. Cold galvanizing is paint with zinc powder. Electroplating deposits a thin zinc layer from a solution. We explained how each method works in the article on galvanizing methods.

Terrace on galvanized ground screw piles

Terrace on galvanized ground screw piles. We worked out how many piles a 4×6 m deck needs in a separate answer

For service life, the difference between hot-dip and cold galvanizing is large. Zinc protects steel twice. First, it shields the metal from soil and water. And if the pile gets scratched, the zinc nearby oxidizes first, and the steel underneath stays intact longer.

Zinc thickness in µm and how it is checked

At SP Premier the zinc thickness on piles is 70 ± 10 µm. On a finished pile this is a layer of 60 to 80 µm. For comparison: 70 µm is 0.07 mm, 43 times thinner than a 3 mm pipe wall. That is why the first period of service life depends on the zinc thickness and the second on the wall.

SP Premier periodically measures the layer thickness on finished piles with a coating thickness gauge. When buying piles, ask the seller for the figure in µm. The word "galvanized" without the layer thickness does not tell you how long the pile will last.

Wall thickness: 2, 2.5 and 3 mm in the SPGS designation

SP Premier states the wall thickness right in the pile name: diameter × wall × length (helix). So there is no need to look for it in the documents. In the standard models:

The thicker the wall, the more metal remains in reserve once the soil has eaten the zinc. Of two piles with the same zinc in the same soil, the one with the thicker wall will last longer.

A separate question is zinc inside the pipe. If water gets into the shaft, corrosion also proceeds from the inside. That is why SP Premier piles are galvanized both outside and inside.

Soil: moisture, acidity, salts and stray currents

The corrosion rate in soil depends on moisture, acidity (pH), salts, oxygen access and stray currents. The more of these factors coincide on a site, the faster the soil removes the zinc and then the steel.

Soil and conditions Risk for the pile Why
Dry, neutral, no salts, deep groundwater Lower Little moisture and salt, corrosion is slow
Constantly moist, high groundwater Higher Water together with dissolved oxygen feeds corrosion
Zone of fluctuating groundwater level High The pile is alternately flooded and dried out, and air brings oxygen
Acidic soil, peat, peat bog High An acidic environment actively dissolves zinc
Saline soil High Salts accelerate the corrosion of zinc and steel
Railway or transformer substation nearby High Stray currents in the soil accelerate metal corrosion

You do not have to determine the soil type yourself. Just tell us what you see on the site: what soil comes up when digging, whether water stands in spring, whether there is a railway or substation nearby. If you have a geological survey, send it too. Based on this description, we will select a pile.

Damage during installation

Zinc suffers not only in the ground but also during installation. Scratches from a wrench or grip, impacts against stones in the soil, welding of the pile head: in these places the steel is left without a zinc layer. Small scratches are not a problem: zinc protects steel electrochemically, and as long as there is plenty of coating on the pile around the scratch, rust does not develop in it. The weld of the pile head needs more attention; more on that below.

If you install the piles yourself, inspect each pile after screwing it in: treat large areas of exposed metal near the ground surface with zinc-rich paint straight away. If you do not want to install them yourself, SP Premier crews will handle ground screw pile installation: they work with hydraulic rigs mounted on an AVANT loader and a MOROOKA tracked carrier.

Installing a ground screw pile with a hand-held electric driver

Installing a pile with a hand-held electric driver for ground screw piles: after screwing it in, check for bare metal

The weakest spot is not underground

A pile rusts fastest at the soil–air boundary and near the weld of the pile head. At the ground line the metal gets moisture and oxygen at the same time, and these are the main conditions for corrosion. When the pile head is welded, the zinc near the weld burns off, and the steel there is left exposed.

There are three simple rules for this zone:

  1. Treat the weld with zinc-rich paint immediately after welding the pile head. This is exactly where cold galvanizing belongs: it patches local damage.
  2. Do not cover the pile head with soil. The pile head and the top of the pile must stay in the open air and dry out.
  3. Drain water away from the pile. Water from the roof or the blind area must not run down and pool around the shaft.

The most active corrosion zone of a ground screw pile is the soil–air boundary and the zone of fluctuating water level.

Galvanized ground screw pile with its head above ground level

The top of the pile and the pile head should stay in the air, not in the soil

Should a pile be filled with concrete?

Concrete inside the pipe does not replace zinc. A pile corrodes primarily from the outside, where the wall is in contact with the soil, and concrete in the shaft does not cover the outer surface. Zinc on the outer wall works the same whether there is concrete inside or not.

Some sellers offer filling the shaft with concrete as a substitute for zinc or promise a percentage increase in service life from it. No page provides a calculation to back up these percentages.

SP Premier's position is as follows. A galvanized pile does not need concrete filling if the distance from the ground to the flange is no more than 600 mm. On slopes, where the distance from the ground to the flange exceeds 600 mm, the shaft can be filled with a cement-sand mix: within 2–3 days it absorbs moisture from the soil and hardens. Concrete is poured into the shaft only in a combined foundation with a concrete grillage on piles: then the top of the pile is concreted together with the grillage.

Warranty and service life are different things

A warranty is the manufacturer's responsibility for the product over a set period. Service life is a calculation of how long the pile will last in a given soil. At SP Premier the warranty on ground screw piles is 20 years, and the estimated service life is 50–120 years. We do not mix these figures: 50–120 years is not a warranty.

What to ask when you see a warranty like this in a listing:

  • "50-year warranty with a 100-year service life". Ask what exactly the warranty covers and under what conditions: soil, installation, weld treatment.
  • "Lifetime warranty". Ask for a written warranty document. Without a document you cannot make a claim against anyone.
  • "Service life 100+ years". Ask for the zinc thickness in µm, the wall thickness and the soil the estimate was made for.

A warranty answers the question "who pays if something goes wrong". Service life answers "how many years the pile carries the load in this soil".

How to check a pile before buying

Six questions to the seller are enough. It is a few minutes of conversation, and the answers will show whether there is a calculation behind the service life figure. You can simply forward the list to the seller in a messenger.

  1. Galvanizing method in the document. It should say "hot-dip galvanizing", not just "galvanized" without details.
  2. Zinc thickness in µm. At SP Premier it is 70 ± 10 µm.
  3. Wall thickness in the designation. For example, "3" in SPGS F 60 × 3 × 1200 (500) means a 3 mm wall.
  4. Zinc inside the pipe. Ask whether the shaft is galvanized on the inside.
  5. Even coating. No drips, stains or areas of exposed metal, especially on the blade and near welds.
  6. Galvanizing standard. For hot-dip galvanizing, DIN EN ISO 1461.

For SP Premier piles, the answers to all questions except the fifth are already in this article, and all standard piles with their parameters are in the ground screw pile catalog.

When a galvanized pile will not reach the stated service life

The 50–120 year estimate does not apply in every soil. On some sites the soil itself shortens the service life of a pile:

  • highly saline soils — salts accelerate the corrosion of zinc and steel;
  • acidic soils and peat bogs — an acidic environment dissolves zinc faster;
  • zone of fluctuating groundwater level — the pile is alternately wet and dry;
  • sites near a railway or transformer substation — stray currents in the soil.

On such sites the pile is selected for the soil individually, and sometimes it is more honest to consider another type of foundation. At SP Premier we ask about the soil first and only then recommend a pile: send us a description of the site, and we will tell you whether a galvanized pile will reach its estimated service life in your particular soil.

Questions from customers

How many years does a galvanized ground screw pile last?

A galvanized SP Premier pile with 70 ± 10 µm hot-dip galvanizing is designed for at least 50 years, and up to 120 years in non-aggressive soil. This is an estimate of service life based on metal thickness and corrosion rate, not a warranty.

Does a ground screw pile rust in the ground?

Yes, any steel in soil corrodes over time. Zinc slows this process: the soil first removes the zinc layer and only then starts thinning the pipe wall. The rate depends on moisture, acidity, salts and stray currents on the site.

Which is better: a galvanized or a painted pile?

For service life, a hot-dip galvanized pile is better. Paint scratches easily during screwing, and the steel under the scratch is immediately in contact with the soil. Zinc bonded with the steel holds on more firmly, and near a small scratch it oxidizes first itself.

Does a galvanized pile need painting?

There is no need to paint the whole hot-dip galvanized pile. Zinc-rich paint is applied only where the zinc is damaged: the weld of the pile head and deep scratches after installation.

Can a pile be filled with concrete to make it last longer?

Concrete inside does not protect the outer wall that is in contact with the soil, so it does not replace zinc. A galvanized pile with no more than 600 mm from the ground to the flange does not need concrete filling. On slopes, when the flange is more than 600 mm above the ground, the shaft is filled with a cement-sand mix. The top of the pile is filled with concrete only together with a concrete grillage.

How long does a ground screw pile foundation last compared with a concrete one?

A ground screw pile foundation lasts as long as the piles last in that soil: for SP Premier piles, an estimated 50–120 years. On top, the piles are tied together by a frame: a steel channel or I-beam, a profile pipe, a timber beam or a reinforced concrete grillage. Its service life depends on the material. The service life of a concrete foundation likewise depends on the concrete, the reinforcement and the soil, so there is no single figure to compare.

What is the warranty on SP Premier piles?

SP Premier ground screw piles come with a 20-year warranty. The estimated service life of 50–120 years is a separate estimate, not a warranty.

Steel frame on SP Premier ground screw piles

The frame ties the piles together at the top, and its service life depends on the material

What to do next

The article on calculating a ground screw pile foundation will help you work out how many piles you need and of what size, and the parameters of the standard models are collected in the ground screw pile catalog.

If you do not want to do the calculation yourself, message or call us at +38 050 431-70-60 (Viber, WhatsApp, Telegram): based on a description of the soil and the structure, we will select an SP Premier pile and calculate the foundation for a site in Kyiv or the Kyiv region.

Contact us to select galvanized SP Premier ground screw piles for your soil!

 Phone: +38 050 431-70-60

 Viber: +38 050 431-70-60

 WhatsApp: +38 050 431-70-60

 Telegram: +38 050 431-70-60

 E-mail: info@sppremier.com.ua

View SP Premier ground screw piles in the catalog